US SAILING

Special Regulations - Extract for Race Category 3 Monohulls


JANUARY 2006 - DECEMBER 2007
 © ORC Ltd. 2002, all amendments from 2003 © International Sailing Federation, (IOM) Ltd.
Version 5.03

Notes
 Red type indicates a significant change in 2006
The use of the masculine gender shall be taken to mean either gender
 Guidance notes and recommendations are in italics

      US SAILING prescriptions are printed in bold, italic letters
Because this is an extract not all paragraph numbers will be present
SECTION 1 - FUNDAMENTAL AND DEFINITIONS
1.01 Purpose and Use
1.01.1 It is the purpose of these Special Regulations to establish uniform minimum equipment, accommodation and training standards for monohull and multihull yachts racing offshore. A Proa is excluded from these regulations.
1.01.2 These Special Regulations do not replace, but rather supplement, the requirements of governmental authority, the Racing Rules and the rules of Class Associations and Rating Systems. The attention of persons in charge is called to restrictions in the Rules on the location and movement of equipment.
1.01.3 These Special Regulations, adopted internationally, are strongly recommended for use by all organizers of offshore races. Race Committees may select the category deemed most suitable for the type of race to be sailed.
1.02 Responsibility of Person in Charge
1.02.1 The safety of a yacht and her crew is the sole and inescapable responsibility of the person in charge who must do his best to ensure that the yacht is fully found, thoroughly seaworthy and manned by an experienced crew who have undergone appropriate training and are physically fit to face bad weather. He must be satisfied as to the soundness of hull, spars, rigging, sails and all gear. He must ensure that all safety equipment is properly maintained and stowed and that the crew know where it is kept and how it is to be used.
1.02.2 Neither the establishment of these Special Regulations, their use by race organizers, nor the inspection of a yacht under these Special Regulations in any way limits or reduces the complete and unlimited responsibility of the person in charge.
1.02.3 Decision to race -The responsibility for a yacht's decision to participate in a race or to continue racing is hers alone - RRS Fundamental Rule 4.
1.03 Definitions, Abbreviations, Word Usage
1.03.1 Definitions of Terms used in this document
      TABLE 1
     
Age Date Month/year of first launch
AIS Automatic Identification Systems
CEN Comité Européen de Normalisation
CPR Cardio-Pulmonary Resuscitation
Coaming includes the transverse after limit of the cockpit over which water would run in the event that when the yacht is floating level the cockpit is flooded or filled to overflowing.
DSC Digital Selective Calling
EN European Norm
EPFS Electronic Position-Fixing System
EPIRB Electronic Position-Indicating Radio Beacon
FA Station The transverse station at which the upper corner of the transom meets the sheerline.
Foul-Weather Suit A foul weather suit is clothing designed to keep the wearer dry and maybe either a jacket and trousers worn together, or a single garment comprising jacket and trousers.
GMDSS Global Maritime Distress & Safety System
GNSS Global Navigation Satellite System
GPIRB EPIRB, with integral GPS position-fixing
ITU International Telecommunications Union
GPS Global Positioning System
Hatch The term hatch includes the entire hatch assembly and also the lid or cover as part of that assembly (the part itself may be described as a hatch).
INMARSAT International Maritime Satellite Organization
IMO International Maritime Organisation
IMSO International Mobile Satellite Organisation (works closely with INMARSAT)
ISAF International Sailing Federation.
ISO International Standard or International Organization for Standardization.
Lifeline wire line rigged as guardrail / guardline around the deck
LOA Length overall not including pulpits, bowsprits, boomkins etc.
LWL (Length of) loaded waterline
Monohull Yacht in which the hull depth in any section does not decrease towards the centre-line.
Moveable Ballast Lead or other material including water which has no practical function in the boat other than to increase weight and/or to influence stability and/or trim and which may be moved transversely but not varied in weight while a boat is racing.
ORC Offshore Racing Congress (formerly Offshore Racing Council)
OSR Offshore Special Regulation(s)
Permanently Installed Means the item is effectively built-in by eg bolting, welding, glassing etc. and may not be removed for or during racing.
PLB Personal Locator Beacon
Proa Asymmetric Catamaran
RRS ISAF - Racing Rules of Sailing
SAR Search and Rescue
SART Search and Rescue Transponder
Series Date Month/year of first launch of the first yacht of the production series
SOLAS Safety of Life at Sea Convention
Safety Line A tether used to connect a safety harness to a strong point
Securely Fastened Held strongly in place by a method (eg rope lashings, wing-nuts) which will safely retain the fastened object in severe conditions including a 180 degree capsize and allows for the item to be removed and replaced during racing
Static Ballast Lead or other material including water which has no practical function in the boat other than to increase weight and/or to influence stability and/or trim and which may not be moved or varied in weight while a boat is racing.
Static Safety Line A safety line (usually shorter than a safety line carried with a harness) kept clipped on at a work-station
Variable Ballast Water carried for the sole purpose of influencing stability and/or trim and which may be varied in weight and/or moved while a boat is racing.
1.03.2 The words "shall" and "must" are mandatory, and "should" and "may" are permissive.
1.03.3 The word "yacht" shall be taken as fully interchangeable with the word "boat".
SECTION 2 - APPLICATION & GENERAL REQUIREMENTS
2.01 Categories of Events
      In many types of race, ranging from trans-oceanic sailed under adverse conditions to short-course day races sailed in protected waters, six categories are established, to provide for differences in the minimum standards of safety and accommodation required for such varying circumstances:
2.01.4 Category 3
      Races across open water, most of which is relatively protected or close to shorelines.
2.02 Inspection
      A yacht may be inspected at any time. If she does not comply with these Special Regulations her entry may be rejected, or she will be liable to disqualification or such other penalty as may be prescribed by the national authority or the race organizers.
2.03 General Requirements
2.03.1 All equipment required by Special Regulations shall:-
     
a) function properly
     
b) be regularly checked, cleaned and serviced
     
c) when not in use be stowed in conditions in which deterioration is minimised
     
d) be readily accessible
     
e) be of a type, size and capacity suitable and adequate for the intended use and size of the yacht.
2.03.2 Heavy items:
     
a) ballast, ballast tanks and associated equipment shall be permanently installed
     
b) heavy movable items including e.g. batteries, stoves, gas bottles, tanks, toolboxes and anchors and chain shall be securely fastened
     
c) heavy items for which fixing is not specified in Special Regulations shall be permanently installed or securely fastened, as appropriate
2.03.3 When to show navigation lights
     
a) navigation lights (OSR 3.27) shall be shown as required by the International Regulations for Preventing Collision at Sea, (Part C and Technical Annex 1). All yachts shall exhibit sidelights and a sternlight at the required times.
SECTION 3 - STRUCTURAL FEATURES, STABILITY, FIXED EQUIPMENT
3.01 Strength of Build, Ballast and Rig
      Yachts shall be strongly built, watertight and, particularly with regard to hulls, decks and cabin trunks capable of withstanding solid water and knockdowns. They must be properly rigged and ballasted, be fully seaworthy and must meet the standards set forth herein. Shrouds shall never be disconnected.
3.02 Watertight Integrity of a Hull
3.02.1 A hull, including, deck, coach roof, windows, hatches and all other parts, shall form an integral, essentially watertight unit and any openings in it shall be capable of being immediately secured to maintain this integrity.
3.02.2 Centreboard and daggerboard trunks and the like shall not open into the interior of a hull except via a watertight inspection/maintenance hatch of which the opening shall be entirely above the waterline of the yacht floating level in normal trim.
3.02.3 A canting keel pivot shall be completely contained within a watertight enclosure which shall comply with OSR 3.02.2. Access points in the watertight enclosure for control and actuation systems or any other purpose shall comply with OSR 3.02.1.
3.02.4 Moveable ballast systems shall be fitted with a manual control and actuation secondary system which shall be capable of controlling the full sailing load of the keel in the event of failure of the primary system. Such failures would include electrical and hydraulic failure and mechanical failure of the components and the structure to which it mounts. The system must be capable of being operational quickly and shall be operable at any angle of heel. It would be desirable if this system was capable of securing the keel on the centreline.
3.04 Stability - Monohulls
3.04.2 A yacht shall be designed and built to resist capsize.
3.04.3 A National Authority or race organizer should require compliance with a minimum stability or stability/buoyancy index. Attention is drawn to the stability index in IMS Regulation 201.
3.04.4 Achievement of Design Category B under ISO 12217-2 may be accepted by a race organizer as a guide to general suitability for competition in a Special Regulations Category 3 race.
3.04.5 Use of the ISO or any other index does not guarantee total safety or total freedom of risk from capsize or sinking.
3.04.6 For boats with moveable or variable ballast the method in OSR 3.04.4 shall apply plus the relevant additional requirement of OSR Appendix K.
3.04.7 Tanks for variable ballast shall be permanently installed and shall be provided with a system of isolating valves and pump(s) capable of manual operation at any angle of heel. A plan of the plumbing system shall be displayed aboard the boat
3.06 Exits - Monohulls
      TABLE 4
     
LOA Earliest of Age or Series Date Detail
8.5 m (28 ft) and over 1/95 and after Yachts shall have at least two exits. At least one exit shall be located forward of the foremost mast except where structural features prevent its installation.
3.08 Hatches & Companionways
3.08.1 No hatch forward of the maximum beam station shall open in such a way that the lid or cover moves into the open position towards the interior of the hull (excepting ports having an area of less than 0.071m2 (110 sq in)).
3.08.2 A hatch shall be:
     
a) so arranged as to be above the water when the hull is heeled 90 degrees
US SAILING prescribes that 3.08.2(a) shall not apply in 2007.
     
b) permanently attached
     
c) capable of being firmly shut immediately and remaining firmly shut in a 180 degree capsize (inversion)
3.08.3 A companionway hatch extending below the local sheerline, shall:
     
a) not be permitted in a yacht with a cockpit opening aft to the sea (OSR 3.09.6)
     
b) be capable of being blocked off up to the level of the local sheerline, provided that the companionway hatch shall continue to give access to the interior with the blocking devices (e.g. washboards) in place
3.08.4 A companionway hatch shall:
     
a) be fitted with a strong securing arrangement which shall be operable from the exterior and interior including when the yacht is inverted
     
b) have any blocking devices
     
       i capable of being retained in position with the hatch open or shut
     
      ii whether or not in position in the hatchway, secured to the yacht (e.g. by lanyard) for the duration of the race, to prevent their being lost overboard
     
     iii permit exit in the event of inversion
3.09 Cockpits - Attention is Drawn to ISO 11812
3.09.1 Cockpits shall be structurally strong, self-draining quickly by gravity at all angles of heel and permanently incorporated as an integral part of the hull.
3.09.2 Cockpits must be essentially watertight, that is, all openings to the hull must be capable of being strongly and rigidly secured
3.09.3 A bilge pump outlet pipe shall not be connected to a cockpit drain . See OSR 3.09.8 for cockpit drain minimum sizes
3.09.4 A cockpit sole shall be at least 2% LWL above LWL (or in IMS yachts first launched before 1/03, at least 2% L above LWL)
3.09.5 A bow, lateral, central or stern well shall be considered a cockpit for the purposes of OSR 3.09
3.09.6 In cockpits opening aft to the sea structural openings aft shall be not less in area than 50% maximum cockpit depth x maximum cockpit width.
3.09.7 Cockpit Volume
      TABLE 5
     
earliest of age or series date detail race category
before 4/92 the total volume of all cockpits below lowest coamings shall not exceed 6% (LWL x maximum beam x freeboard abreast the cockpit). MoMu0,1
before 4/92 the total volume of all cockpits below lowest coamings shall not exceed 9% (LWL x maximum beam x freeboard abreast the cockpit). MoMu2,3,4
4/92 and after as above for the appropriate category except that "lowest coamings" shall not include any aft of the FA station and no extension of a cockpit aft of the working deck shall be included in calculation of cockpit volume **
Note IMS-rated boats may instead of the terms LWL, maximum beam, freeboard abreast the cockpit, use the IMS terms L, B and FA. **
3.09.8 Cockpit Drains
      See OSR 3.09.1. Cockpit drain cross section area (after allowance for screens if fitted) shall be:-
     
a) in yachts with earliest of age or series date before 1/72 or in any yacht under 8.5m (28ft) LOA - at least that of 2 x 25mm diameter (one inch) unobstructed openings or equivalent
     
b) in yachts with earliest of age or series date 1/72 and later - at least that of 4 x 20mm diameter (3/4 inch) unobstructed openings or equivalent
      US SAILING prescribes that cockpit drains shall be accessible for cleaning
3.10 Sea Cocks or Valves
      Sea cocks or valves shall be permanently installed on all through-hull openings below LWL except integral deck scuppers, speed indicators, depth finders and the like, however a means of closing such openings shall be provided.
3.11 Sheet Winches
      Sheet winches shall be mounted in such a way that an operator is not required to be substantially below deck.
3.12 Mast Step
      The heel of a keel stepped mast shall be securely fastened to the mast step or adjoining structure.
3.14 Pulpits, Stanchions, Lifelines - Attention is Drawn to ISO 15085
3.14.2 Lifelines required in Special Regulations shall be "taut".
     
a) As a guide, when a deflecting force of 50 N (5.1 kgf, 11.2 lbf) is applied to a lifeline midway between supports, the lifeline should not deflect more than 50 mm.
3.14.3 The following shall be provided:
     
a) a bow pulpit forward of the headstay (however on yachts under 8.5 m (28 ft) the bow pulpit may be aft of the headstay provided the forward upper rail is within 405 mm (16 in) of the headstay) with vertical height and openings essentially conforming to Table 7 Bow pulpits may be open but the opening between the pulpit and any part of the boat shall never be greater than 360mm (14.2") (this requirement shall be checked by presenting a 360mm (14.2") circle inside the opening)
     
b) a stern pulpit, or lifelines arranged as an adequate substitute, with vertical openings conforming to Table 7
     
c) lifelines (guardlines) supported on stanchions, which, with pulpits, shall form an effectively continuous barrier around a working deck for man-overboard prevention. Lifelines shall be permanently supported at intervals of not more than 2.20m (86.6") and shall not pass outboard of supporting stanchions
     
d) upper rails of pulpits at no less height above the working deck than the upper lifelines as in Table 7.
     
e) Openable upper rails in bow pulpits shall be secured shut whilst racing
     
f) Pulpits and stanchions shall be permanently installed. When there are sockets or studs, these shall be through-bolted, bonded or welded. The pulpit(s) and/or stanchions fitted to these shall be mechanically retained without the help of the life-lines. Without sockets or studs, pulpits and/or stanchions shall be through-bolted, bonded or welded.
     
g) The bases of pulpits and stanchions shall not be further inboard from the edge of the appropriate working deck than 5% of maximum beam or 150 mm (6 in), whichever is greater.
     
h) Stanchion bases shall not be situated outboard of a working deck. For the purpose of this rule a stanchion or pulpit base shall be taken to include a sleeve or socket into which a stanchion or pulpit tube is fitted but shall exclude a baseplate which carries fixings into the deck or hull.
     
i) Provided the complete lifeline enclosure is supported by stanchions and pulpit bases effectively within the working deck, lifeline terminals and support struts may be fixed to a hull aft of the working deck
     
j) Lifelines need not be fixed to a bow pulpit if they terminate at, or pass through, adequately braced stanchions set inside and overlapping the bow pulpit, provided that the gap between the upper lifeline and the bow pulpit does not exceed 150 mm (6 in).
     
k) Stanchions shall be straight and vertical except that:-
     
i) within the first 50 mm (2 in) from the deck, stanchions shall not be displaced horizontally from the point at which they emerge from the deck or stanchion base by more than 10 mm (3/8 in),and
     
ii) stanchions may be angled to not more than 10 degrees from vertical at any point above 50 mm (2 in) from the deck.
3.14.5 Lifeline Height, Vertical Openings, Number of Lifelines
      TABLE 7
     
LOA earliest of age/seriesdate minimum requirements Category
under 8.5 m(28 ft) before1/92 taut single lifeline at a height of no less than 450 mm (18 in) above the working deck. No vertical opening shall exceed 560 mm (22 in). **
under 8.5 m(28 ft) 1/92and after as for under 8.5 m(28 ft) in table 7 above, except that when an intermediate lifeline is fitted no vertical opening shall exceed 380 mm (15 in). **
8.5 m (28 ft) and over before1/93 taut double lifeline with upper lifeline at a height of no less than 600 mm (24 in) above the working deck. No vertical opening shall exceed 560 mm (22 in) **
8.5 m (28 ft)and over 1/93 and after as 8.5 m (28 ft) and over in Table 7 above, except that no vertical opening shall exceed 380 mm (15 in). **
all all on yachts with intermediate lifelines the intermediate line shall be not less than 230 mm (9 in) above the working deck and shall be of the same construction and general arrangements as required for the upper. **
3.14.6 Lifeline Minimum Diameters, Required Materials, Specifications
     
a) All lifelines shall be stranded stainless steel wire of minimum diameter in table 8 below. Lifelines shall be uncoated and used without close-fitting sleeving.
      Notwithstanding 3.14.6 (a), temporary sleeving may be fitted provided it is regularly removed for inspection
     
b) Grade 316 stainless wire is recommended.
     
c) A taut lanyard of synthetic rope may be used to secure lifelines provided the gap it closes does not exceed 100 mm (4 in).
     
d) All wire, fittings, anchorage points, fixtures and lanyards shall comprise a lifeline enclosure system which has at all points at least the breaking strength of the required lifeline wire.
      TABLE 8
     
LOA minimum wire diameter
under 8.5 m (28ft) 3 mm (1/8 in)
8.5m - 13 m 4 mm (5/32 in)
over 13 m (43 ft) 5 mm (3/16 in)
3.14.7 Pulpits, Stanchions, Lifelines - Limitations on Materials
      TABLE 9
     
Earliest of Age or Series Date detail
before 1/87 carbon fibre is not recommended in stanchions pulpits and lifelines.
1/87 and after stanchions, pulpits and lifelines shall not be made of carbon fibre.
3.17 Toe Rail or Foot - Stop
3.17.1 A toe rail of minimum height 25 mm (1 in) shall be permanently installed around the foredeck from abreast the mast, except in way of fittings and not further inboard from the edge of the working deck than one third of the local half-beam.
3.17.2 The following variations shall apply:-
      TABLE 10
     
LOA Earliest of Age or Series Date minimum requirements
any before 1/81 a toe rail minimum height of 20 mm (3/4 in) is acceptable.
any before 1/93 an additional lifeline of minimum height 25 mm (1 in) and maximum height 50 mm (2 in) is acceptable in lieu of a toe rail (but shall not count as an intermediate lifeline).
any 1/94 and after the toe rail shall be fitted as close as practicable to the vertical axis of stanchion bases but not further inboard than 1/3 the local half-beam.
3.18 Toilet
3.19 Bunks
3.19.2 Bunks, permanently installed
3.20 Cooking Facilities
3.20.1 A cooking stove, permanently installed or securely fastened with safe accessible fuel shutoff control and capable of being safely operated in a seaway.
3.21 Drinking Water Tanks & Drinking Water
3.21.1 Drinking Water Tanks
     
a) A yacht shall have a permanently installed delivery pump and water tank(s):
3.21.3 Emergency Drinking Water
     
a) At least 9 litres (2 UK gallons, 2.4 US gallons) of drinking water for emergency use shall be provided in a dedicated and sealed container or container(s)
3.22 Hand Holds
      Adequate hand holds shall be fitted below deck so that crew members may move about safely at sea.
      A hand hold should be capable of withstanding without rupture a side force of 1500N - attention is drawn to ISO 15085.
3.23 Bilge Pumps and Buckets
3.23.1 No bilge pump may discharge into a cockpit unless that cockpit opens aft to the sea.
3.23.2 Bilge pumps shall not be connected to cockpit drains. (OSR 3.09)
3.23.3 Bilge pumps and strum boxes shall be readily accessible for maintenance and for clearing out debris
3.23.4 Unless permanently installed, each bilge pump handle shall be provided with a lanyard or catch or similar device to prevent accidental loss
3.23.5 The following shall be provided:
     
d) at least one permanently installed manual bilge pump operable with all cockpit seats, hatches and companionways shut
     
f) two buckets of stout construction each with at least 9 litres (2 UK gallons, 2.4 US gallons) capacity. Each bucket to have a lanyard.
3.24 Compass
3.24.1 The following shall be provided:-
     
a) a marine magnetic compass, independent of any power supply, permanently installed and correctly adjusted with deviation card, and
     
b) a compass which may be hand-held
3.25 Halyards.
      No mast shall have less than two halyards, each capable of hoisting a sail.
      Boom Support. US SAILING prescribes that some means must exist to prevent the boom from dropping if support from the mainsail and/or halyard fails. Topping lifts or supporting vangs are acceptable for this purpose.
3.27 Navigation Lights (see OSR 2.03.3)
3.27.1 Navigation lights shall be mounted so that they will not be masked by sails or the heeling of the yacht.
3.27.2 Navigation lights shall not be mounted below deck level and should be at no less height than immediately under the upper lifeline.
3.27.3 Navigation light intensity
      TABLE 11
     
LOA Guide to required minimum power rating for an electric bulb in a navigation light
under 12 m (39.4 ft) 10 W
12 m (39.4 ft) and above 25 W
      US SAILING prescribes that in the US compliance with the recommendations of COLREGS shall suffice in satisfying these regulation, COLREGS requirements are as follows;
      TABLE 14
     
LOA Light Luminous Intensity Minimum Range
         of visibility
under 39.4 ft Side 0.9 candelas 1 mile
   Stern 4.3 candelas 2 miles
39.4 ft and above Side 4.3 candelas 2 miles
and less than 164 ft Stern 4.3 candelas 2 miles
3.27.4 Reserve navigation lights shall be carried having the same minimum specifications as the navigation lights above, with a separable power source, and wiring or supply system essentially separate from that used for the normal navigation lights
3.27.5 spare bulbs for navigation lights shall be carried, or for lights not dependent on bulbs, appropriate spares.
3.28 Engines, Generators, Fuel
3.28.1.1 A propulsion engine shall be provided, EITHER as a securely covered inboard engine together with permanently installed exhaust and fuel supply systems and fuel tank(s) OR as an outboard engine with associated tanks and fuel supply systems, all securely fastened.
3.28.2 A propulsion engine shall be provided, EITHER as a securely covered inboard engine together with permanently installed exhaust and fuel supply systems and fuel tank(s) OR in a multihull of less than 12.0m (39.4ft) as an outboard engine with associated tanks and fuel supply systems, all securely fastened.
     
a) A separate generator for electricity is optional. However, when a separate generator is carried it shall be permanently installed, securely covered, and shall have permanently installed exhaust and fuel supply systems and fuel tank(s). A separate generator shall comply with OSR 3.28.3 (c) and (e)
3.28.3 A propulsion engine required by Special Regulations shall:-
     
a) provide a minimum speed in knots of (1.8 x square root of LWL in metres) or (square root of LWL in feet)
     
b) have a minimum amount of fuel which may be specified in the Notice of Race but if not, shall be sufficient to be able to meet charging requirements for the duration of the race and to motor at the above minimum speed for at least 8 hours
     
c) have adequate protection from the effects of heavy weather
     
d) when an electric starter is the only method for starting the engine, have a separate battery, the primary purpose of which is to start the engine
     
e) have each fuel tank provided with a shutoff valve. Except for permanently installed linings or liners, a flexible tank is not permitted as a fuel tank.
3.28.4 Batteries
     
b) It is recommended that consideration be given to the installation of sealed batteries, noting however that a special charging device may be specified by the battery manufacturers
3.29 Communications Equipment, EPFS (Electronic Position-Fixing System), Radar, AIS
      Provision of GMDSS and DSC is unlikely to be mandatory for small craft during the term of the present Special Regulations However it is recommended that persons in charge include these facilities when installing new equipment.
3.29.1 The following shall be provided:
     
a) A marine radio transceiver (or if stated in the Notice of Race, an installed satcom terminal), and
     
       i an emergency antenna when the regular antenna depends upon the mast.
     
b) When the marine radio transceiver is VHF:
     
       i it shall have a rated output power of 25W
     
      ii it shall have a masthead antenna, and co-axial feeder cable with not more than 40% power loss
     
     iii the following types and lengths of co-axial feeder cable will meet the requirements of OSR 3.29.1 (b)(ii): (a) up to 15m (50ft) - type RG8X ("mini 8"); (b) 15-28m (50-90ft) - type RG8U; (c) 28-43m (90-140ft) - type 9913F (uses conventional connectors, available from US supplier Belden); (d) 43-70m) 140-230ft - type LMR600 (uses special connectors, available from US supplier Times Microwave).
     
      iv it should include channel 72 (an international ship-ship channel which, by common use, has become widely accepted as primary choice for ocean racing yachts anywhere in the world)
     
f) Independent of a main radio transceiver, a radio receiver capable of receiving weather bulletins
     
i) An EPFS (Electronic Position-Fixing System) (e.g. GPS)
4.29.2 Yachts are reminded that no reflector, active or passive, is a guarantee of detection or tracking by a vessel using radar.
     
a) The attention of persons in charge is drawn to legislation in force or imminent affecting the territorial seas of some countries in which the carriage of an AIS set is or will be mandatory for certain vessels including relatively small craft.
SECTION 4 - PORTABLE EQUIPMENT & SUPPLIES for the yacht (for water & fuel see OSR 3.21 and OSR 3.28)
4.01 Sail Letters & Numbers
4.01.1 Yachts which are not in an ISAF International Class or Recognized Class shall comply with RRS 77 and Appendix G as closely as possible, except that sail numbers allotted by a State authority are acceptable .
4.01.2 Sail numbers and letters of the size carried on the mainsail must be displayed by alternative means when none of the numbered sails is set.
4.03 Soft Wood Plugs
      Soft wood plugs, tapered and of the appropriate size, shall be attached or stowed adjacent to the appropriate fitting for every through-hull opening.
4.04 Jackstays, Clipping Points and Static Safety Lines
4.04.1 The following shall be provided:
     
a) Jackstays:-
      shall be provided-
     
       i attached to through-bolted or welded deck plates or other suitable and strong anchorage fitted on deck, port and starboard of the yacht's centre line to provide secure attachments for safety harness:-
     
      ii comprising stainless steel 1 x 19 wire of minimum diameter 5 mm (3/16 in), or webbing of equivalent strength;
      US SAILING prescribes that jackstays may be of configurations other than 1 X 19.
     
     iii which, when made from stainless steel wire shall be uncoated and used without any sleeving;
     
      iv 20kN (2,040 kgf or 4,500 lbf) min breaking strain webbing is recommended;
4.04.2 Clipping Points:-
      shall be provided-
     
a) attached to through-bolted or welded deck plates or other suitable and strong anchorage points adjacent to stations such as the helm, sheet winches and masts, where crew members work for long periods:-
     
b) which, together with jackstays and static safety lines shall enable a crew member-
     
       i to clip on before coming on deck and unclip after going below;
     
      ii whilst continuously clipped on, to move readily between the working areas on deck and the cockpit(s) with the minimum of clipping and unclipping operations.
     
e) Warning - U-bolts as clipping points - see OSR 5.02.1(a)
4.05 Fire Extinguishers
      Shall be provided as follows:
4.05.1 Fire extinguishers, at least two, readily accessible in suitable and different parts of the yacht
4.06 Anchor(s)
4.06.1 An anchor or anchors shall be carried according to the table below:
      TABLE 12
     
LOA detail race category
any The specification of anchor, chain and rope shall be in accordance with relevant class rules or the rules of a recognised Classification Society (eg Lloyd’s, DNV, etc.) MoMu0
8.5 m (28 ft) and over 2 anchors together with a suitable combination of chain and rope, all ready for immediate use MoMu1,2,3
under 8.5 m (28 ft) 1 anchor together with a suitable combination of chain and rope, all ready for immediate use MoMu1,2,3
any 1 anchor, readily accessible MoMu4
4.07 Flashlight(s)
4.07.1